Results 1 to 18 of 18

Thread: Lee Auto Prime

  1. #1
    Brass Trader WarEagleEd's Avatar
    Join Date
    May 2013
    Posts
    321
    Feedback Score
    6 (100%)

    Lee Auto Prime

    I recently bought a lot of reloading equipment. It was a mix of stuff but I found a Lee Auto Prime (not the Auto Prime XR) hand operated primer. Are these pretty good tools or are they more trouble then they are worth. Do the shell holders for the XR model fit the old model?

    Ed

  2. #2
    Senior Member
    Join Date
    Jul 2013
    Posts
    132
    Feedback Score
    8 (100%)
    It does use the same shell holders as the XR, as per lee's web site. I think my lee reloading manual talks about it. If you don't have the book, I can check for you.

  3. #3
    Brass Trader
    Join Date
    Mar 2013
    Posts
    704
    Feedback Score
    18 (100%)
    The auto prime and auto prime XR are basically the same with the exception of a small blast shield on the XR that comes up when the ram is raised, just to prevent primer mass detonation. The shell holders should be the same between the old and new version as the ergo prime uses the same shell holders too.

    As to how good of a tool it is, I like every lee tool I've tried with only one exception (quick trim set). I've stuffed in a few thousand primers of different makes with my XR and haven't had a single detonation, when I quite probably should have... I've had primers go in upside down and sideways and they still haven't gone off in my hand. I've loaded federal match primers in 308 with no issues either. Overall I think you'll like the auto prime, I know I like my XR.

  4. #4
    Administrator DukeInFlorida's Avatar
    Join Date
    Feb 2013
    Posts
    248
    Feedback Score
    5 (100%)
    I like doing the priming on the press.

    I use either my RCBS RockChuckers with the spring loaded primer arm, or my Dillon RL550b, with the primer feed tubes.

    Have never, in more than 40 years of doing this, had a primer detonate while setting it. That includes some that ended up, for whatever strange reason, in weird orientations. Upside down, sideways, etc.

    I like to set primers on the machine because the machine gives me maximum leverage, etc. And, I have never been one to want to hurt my hands with a manual primer setter. I shudder when I hear some people talk about setting primers while watching TV, etc. Setting primers is one of the mechanical parts of reloading that demands more attention (attentiveness) than that.

    Administrator - Ammo Brass Trader
    NRA Life Member
    NRA Certified Metallic Cartridge Reloading Instructor

    Author of a book on reloading
    ILSA MEMBER http://www.internationallawnsteelsho...ssociation.com
    NRA RANGE SAFETY OFFICER


  5. #5
    Senior Member
    Join Date
    Jul 2013
    Posts
    132
    Feedback Score
    8 (100%)
    I think a hand primer should get more credit than that Duke. Even with all the pain of tennis elbow and arthritis (sp?), I don't hurt from using my XR. It also gives me a good feal for the primer being seated. As for paying attention and not watching tv when priming, I would hope that they would do a good QC after, be it on a hand press, a progressive, or a single stage. It is possible to put one in upside down on any of them, or not seat them enough, or even not seat one at all.

  6. #6
    Junior Member
    Join Date
    Jun 2013
    Posts
    10
    Feedback Score
    5 (100%)
    I have only ever used a lee hand prime and it is easy to have them flip sideways and upside down. Do other brand hand primers do this also?

  7. #7
    Brass Trader
    Join Date
    Mar 2013
    Posts
    704
    Feedback Score
    18 (100%)
    All of the 308 I load is single stage, just for consistency, so they get primed by hand. 223 also get primed by hand for now, just because I've had too many non-swaged primer pockets, but it's progressive after that. Straight necked handgun stuff is fully progressive from start to finish.

    As for watching TV while priming, I do that, but if I don't actually look at the primer I at least run a finger across it to feel the seating depth and make sure the primer went in straight... In reality I'm just listening to the TV and sitting in a chair that's a lot more comfortable than the stool at my bench

  8. #8
    Brass Trader WarEagleEd's Avatar
    Join Date
    May 2013
    Posts
    321
    Feedback Score
    6 (100%)
    Quote Originally Posted by jebsca View Post
    If you don't have the book, I can check for you.
    I don't have the Lee manual.

    Quote Originally Posted by DukeInMaine
    I like doing the priming on the press.
    This is what I have been doing and have had good results so far.

    However, I got this hand primer with a bunch of other stuff and am thinking about giving it a try.

    Ed

  9. #9
    Senior Member
    Join Date
    Feb 2013
    Posts
    958
    Feedback Score
    37 (100%)
    Quote Originally Posted by WarEagleEd View Post
    I don't have the Lee manual.



    This is what I have been doing and have had good results so far.

    However, I got this hand primer with a bunch of other stuff and am thinking about giving it a try.

    Ed
    I like the hand primer. I get a better feel of when they are set right with the hand tool instead of the press. But some cases (Mainly Winchester 7.62X54R cases) need just a littler more force to get them primed. Then I break out the Lee Ram Primer and do use the press. (Why the Winchester cases have such tight primer pockets I have no clue!)

    Anyways for a manual you can use the Auto Prime XR manual I would guess Like was previously mentioned I think the only difference is the little thingie that lifts the next primer up to feed and would probably stop a chain reaction detonation, which I have never had happen in 35+ years of hand priming.

    Anyways the instruction sheet for the XR can be downloaded for free at :

    http://leeprecision.com/instructions.html

  10. #10
    Brass Trader WarEagleEd's Avatar
    Join Date
    May 2013
    Posts
    321
    Feedback Score
    6 (100%)
    Quote Originally Posted by gandog56;8058
    Anyways the instruction sheet for the XR can be downloaded for free at :

    [URL="http://leeprecision.com/instructions.html"
    http://leeprecision.com/instructions.html[/URL]
    Thanks,

    Ed

  11. #11
    Senior Member
    Join Date
    Feb 2013
    Posts
    958
    Feedback Score
    37 (100%)
    Did that Lee manual I pointed you to help anything?

  12. #12
    Brass Trader WarEagleEd's Avatar
    Join Date
    May 2013
    Posts
    321
    Feedback Score
    6 (100%)
    Quote Originally Posted by gandog56 View Post
    Did that Lee manual I pointed you to help anything?
    It did, thanks!

    Ed

  13. #13
    Brass Trader
    Join Date
    Feb 2013
    Posts
    33
    Feedback Score
    1 (100%)
    I've got 3 AutoPrimes and use them all of the time. A few things to be aware of:

    Lee is no longer offering parts for the old style (round tray) but is offering to replace your old style with a new unit. All you have to do is send them your old unit PLUS 1/2 the cost of a new unit PLUS shipping and they will send you a new style......WHAT A DEAL!?!?!

    Also, you can't prime WSM or WSSM brass on them without grinding out the mouth on the main body.

  14. #14
    Senior Member
    Join Date
    Feb 2013
    Posts
    958
    Feedback Score
    37 (100%)
    Quote Originally Posted by rodnocker1 View Post

    Also, you can't prime WSM or WSSM brass on them without grinding out the mouth on the main body.
    Can you elaborate about that because I don't see why it is necessary.

  15. #15
    Brass Trader
    Join Date
    Feb 2013
    Posts
    33
    Feedback Score
    1 (100%)
    The opening on the tool is about 0.532" (according to my mic) and a WSM case body measures 0.553"+/-. The mouth on the tool isn't wide enough for the WSM case to go in. Midway's site makes a note about it on their Autoprime page and Laine at Lee Precision told me the same thing....use a Dremel tool to remove material. He said the original Autoprime was designed back before the WSM and WSSM cases were introduced.

    I used one of the small sanding drums and just made a single pass, removing material from both sides at once. It now works with WSM brass.
    Last edited by rodnocker1; 10-24-2013 at 11:58 AM.

  16. #16
    Brass Trader WarEagleEd's Avatar
    Join Date
    May 2013
    Posts
    321
    Feedback Score
    6 (100%)
    Quote Originally Posted by rodnocker1 View Post
    Lee is no longer offering parts for the old style (round tray) but is offering to replace your old style with a new unit. All you have to do is send them your old unit PLUS 1/2 the cost of a new unit PLUS shipping and they will send you a new style......WHAT A DEAL!?!?!
    I heard about this but can't find anything on their website about it. I figured I would use it until it breaks and then send it in for the Auto Prime XR, if I am happy with the results I get from the original one I have.

    Ed

  17. #17
    Senior Member
    Join Date
    Feb 2013
    Posts
    958
    Feedback Score
    37 (100%)
    Or, I may have a spare in my shed. You need parts for the old one, contact me first!

    I have both the new one and an Lee Ergo hand primer and don't use the old one any more.

  18. #18
    Brass Trader WarEagleEd's Avatar
    Join Date
    May 2013
    Posts
    321
    Feedback Score
    6 (100%)
    Quote Originally Posted by gandog56 View Post
    Or, I may have a spare in my shed. You need parts for the old one, contact me first!
    Roger that!

    Ed

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check