Search:

Type: Posts; User: WarEagleEd

Page 1 of 13 1 2 3 4
Results 1 to 25 of 320

Search: Search took 0.00 seconds.

  1. Currently, Amazon has ss pins for $19.50 for 2.5...

    Currently, Amazon has ss pins for $19.50 for 2.5 lbs, but you will also be charged tax (state tax in my state is 4% which would make the total bill $20.28). The same pins would be $20.05 from Best...
  2. Duke, Those home-made dummy rounds are pretty...

    Duke,

    Those home-made dummy rounds are pretty cool!

    I tumbled some .32 ACP brass along with some .30 Carbine brass from my dad's decades old stash (LC 52 head stamp).

    All this brass I have...
  3. Replies
    8
    Views
    7,436

    Forum: Brass Trading

    Updated (slightly) .380 Auto, 9mm, and .300...

    Updated (slightly) .380 Auto, 9mm, and .300 Blackout quantities.
  4. I ran some .45 ACP and some .44 Magnum through...

    I ran some .45 ACP and some .44 Magnum through the tumbler. I removed the primers from the .45 over the last two days.
  5. Replies
    8
    Views
    7,436

    Forum: Brass Trading

    Added some more .380 Auto.

    Added some more .380 Auto.
  6. Replies
    8
    Views
    7,436

    Forum: Brass Trading

    Added some .243 Winchester, 9mm, and some more...

    Added some .243 Winchester, 9mm, and some more .30 Carbine.
  7. I use a Lortone model 33B. I use some Lemi-Shine,...

    I use a Lortone model 33B. I use some Lemi-Shine, non-concentrated Dawn dish detergent, and water. I get my stainless steel pins from Best Byte computers in Katy, TX. The Lortone 33B can't process a...
  8. I ran a load of assorted caliber brass through...

    I ran a load of assorted caliber brass through the tumbler and sorted a bunch of brass.
  9. Replies
    8
    Views
    7,436

    Forum: Brass Trading

    New brass added and needs updated.

    New brass added and needs updated.
  10. I sorted and put into containers .30-06 brass...

    I sorted and put into containers .30-06 brass that I tumbled yesterday.
  11. I tumbled some .30-06 brass. I then started...

    I tumbled some .30-06 brass. I then started sorting all the brass I have tumbled over the last several days. This caused me to look over my brass stash and come to the realization that I don't need...
  12. I tumbled some .380 Auto and .38 Special brass...

    I tumbled some .380 Auto and .38 Special brass today.
  13. I removed primers from the rest of my .38 special...

    I removed primers from the rest of my .38 special brass. I've been getting a fair amount done lately. I've tumbled a decent amount of brass, deprimed a bunch of brass, and even ordered more stainless...
  14. I removed the primers from about 50 pieces of...

    I removed the primers from about 50 pieces of 7.62 X 39 brass. What was odd is that 6 of them had unfired primers in them. When I removed them the primer pockets were dirty, so the cases had been...
  15. I removed primers from some .30 Carbine, .300...

    I removed primers from some .30 Carbine, .300 Blackout, and 7.62 X 39. Also, my Lee depriming die started to get some rust on the decapping pin nut and the top of the die, so I've got those soaking...
  16. Replies
    14
    Views
    7,958

    The Lyman AR Reloading Handbook does list 2 cast...

    The Lyman AR Reloading Handbook does list 2 cast boolit loads, one a 160 gr. boolit, the other @ 180 gr. They aren't listed as sub-sonic as they can get up over 1400 fps if loaded toward the high...
  17. I began to clean up my little reloading bench,...

    I began to clean up my little reloading bench, but I didn't get too far as I started too late in the day to accomplish much. I found a couple of hundred pieces of brass of various calibers that I...
  18. I tumbled the 7.62X39 and .32 ACP brass that I...

    I tumbled the 7.62X39 and .32 ACP brass that I deprimed the other day. I just need to find the time to load all this brass that I'm prepping.
  19. I removed the primers from some .32 ACP and...

    I removed the primers from some .32 ACP and 7.62X39 brass. Most of the 7.62X39 brass was "PMC" and the primers were crimped in place, so I'll have to remove the crimp from those cases. The rest of...
  20. I applied some WD-40 as a corrosion preventative...

    I applied some WD-40 as a corrosion preventative on the rams, handles, and other exposed metal parts of my reloading presses.

    Ed
  21. Replies
    7
    Views
    4,304

    Hensley & Gibbs (H&G) molds sure do command a...

    Hensley & Gibbs (H&G) molds sure do command a premium when you see them for sale second hand. I have a couple, but have only cast once with a .45 caliber H&G mold. Since that was one of my first...
  22. Knocking out more primers with the Harvey...

    Knocking out more primers with the Harvey Deprimer.
  23. I knocked the primers out of some .270 Winchester...

    I knocked the primers out of some .270 Winchester range brass using the Harvey Deprimer.
  24. My reloading set-up is in the garage. It is west...

    My reloading set-up is in the garage. It is west facing and gets pretty hot in the Summer which discourages me from doing much reloading. Add in a one-year old and there isn't much time to sit in the...
  25. Replies
    5
    Views
    3,497

    I check the boards pretty frequently, but I have...

    I check the boards pretty frequently, but I have not been able to reload at all lately so I haven't burned through any brass. Therefore, I have no demand for any. Hopefully, that will change soon.
Results 1 to 25 of 320
Page 1 of 13 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check