Search:

Type: Posts; User: Mbaker78

Page 1 of 20 1 2 3 4
Results 1 to 25 of 500

Search: Search took 0.00 seconds.

  1. My local shop had a 50cal ammo can full on M&P40...

    My local shop had a 50cal ammo can full on M&P40 magazines for $12, so I bought a handful of them the other day. Eventually I’ll get around to building a 40s&w upper for my SBR and pick a stern...
  2. Replies
    2
    Views
    64

    For some reason I seem to attract those types...

    For some reason I seem to attract those types when I’m at the range...
  3. Thread: Bullet molds

    by Mbaker78
    Replies
    6
    Views
    107

    I only have experience with lee 2 cavity molds so...

    I only have experience with lee 2 cavity molds so far, but they seem to work well enough for me.
  4. I just used parchment paper. Much less fuss, and...

    I just used parchment paper. Much less fuss, and I can still get a couple uses out of it.
  5. I made it to the range today to put some rounds...

    I made it to the range today to put some rounds through my pistol suppressor. It’s an all around improvement over unsuppressed, but not nearly silent. Brass seems to just pile up at my feet now as...
  6. I finally picked up the rest of the stuff I...

    I finally picked up the rest of the stuff I should need for powder coating, so Iíll probably give that a try sometime today. Hopefully it doesnít go too poorly.

    I tried out a test set of subsonic...
  7. Replies
    7
    Views
    502

    Forum: Brass Trading

    Something will come up somewhere. Just have to be...

    Something will come up somewhere. Just have to be patient.
  8. I decided to try to tumble lube 50 each of the...

    I decided to try to tumble lube 50 each of the bullets I casted up, which turned out to be well over 300 of each over a few days. If the tumble lube goes well I might just stick with that as it’s...
  9. Replies
    5
    Views
    372

    I still try to drop in every couple days, but it...

    I still try to drop in every couple days, but it has been pretty dead lately...
  10. Replies
    6
    Views
    418

    It’s good that you seem to have a positive...

    It’s good that you seem to have a positive attitude toward it. I’ve heard that helps a lot, believe it or not. Hoping for a speedy trip through this and back into remission.

    Side note, have you...
  11. I finally decided to try casting, made up about...

    I finally decided to try casting, made up about 50 each 40 175gr TC, 45 230gr TC, and 308 230gr.

    Once I got the hang of it they went pretty quickly. I still have yet to get the stuff I need to...
  12. I really like the APS strips, so I might look...

    I really like the APS strips, so I might look into the APS bench priming tool, but it doesn’t have the universal shellholder that the hand tool does.
  13. I hand primed 1000 pieces of 40s&w brass the...

    I hand primed 1000 pieces of 40s&w brass the other day. My hand is still sore from that...
  14. I got tired of fighting the case feeder on my...

    I got tired of fighting the case feeder on my loadmaster (I had it running smooth for about 20 minutes) so I decided to modify it so that it’s somewhat manual.

    I put in a small stop to keep the...
  15. Thread: 9mm

    by Mbaker78
    Replies
    12
    Views
    1,038

    Forum: Brass Trading

    Don’t you have to use a Rockwell retroencabulator...

    Don’t you have to use a Rockwell retroencabulator to load them?
  16. Thread: 9mm

    by Mbaker78
    Replies
    12
    Views
    1,038

    Forum: Brass Trading

    sending PM...

    sending PM...
  17. Replies
    11
    Views
    950

    My experience with 458 socom was only with...

    My experience with 458 socom was only with jacketed bullets, but I couldn’t get the powder through expander to open the mouths enough to seat properly and still pass a chamber gauge. I had to use a...
  18. I plan on doing the same thing when I have enough...

    I plan on doing the same thing when I have enough to make it worth the trip. Right now I have 3 1lb coffee cans full of spent primers and a bunch of the neck cutoffs from making 300aac, along with a...
  19. I’ll probably eventually break down and buy 5k...

    I’ll probably eventually break down and buy 5k online. Just have to get some money saved up first.
  20. I’m guessing you go to west chester, I usually go...

    I’m guessing you go to west chester, I usually go to the one on Wilmington pike unless the wife drags me to ikea.

    I hand prime everything anymore since I switched to an APS tool.
  21. Every time I go to my local cabelas they’re...

    Every time I go to my local cabelas they’re completely out of CCI SR primers (400?)
  22. Thread: My Trades

    by Mbaker78
    Replies
    18
    Views
    9,392

    Forum: Brass Trading

    Changed a few things, haven’t bumped in a while.

    Changed a few things, haven’t bumped in a while.
  23. I finally sorted through the brass from my range...

    I finally sorted through the brass from my range trip a few weeks back. I am starting to think that it actually does mate I have almost another quart baggie full of 9mm, and I don’t even own...
  24. Thanks everyone for the kind thoughts and words....

    Thanks everyone for the kind thoughts and words. Though I know we’re not supposed to have favorites, he was definitely my favorite of the pack. We think he was a Malamute and Great Pyrenees mix, but...
  25. I really like the frankford arsenal trim and prep...

    I really like the frankford arsenal trim and prep center for 223. It’s alright for 300aac, but you almost have to use pliers or something to hold the cases.

    I haven’t really done much of anything,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check