Hmmm, I call them code blues.:rolleyes:
Cause if you get hit by one....
Quote:
Code Blue" is generally used to indicate a patient requiring resuscitation or in need of immediate medical attention
Printable View
I meant the lighter blue RFN as opposed to the darker blue TC. Did you powder coat them or buy them that way?
Nah nah nah, I'm MUCH too lazy to do it myself, and I don't cast.
Finished up processing all the 7.62X54R, .380 ACP, .38 special, .357 magnum, .454 Casull, 357 SIG , and .45 Colt from my last range trip. Completely ready for reloading.
Care to share your source for those 40/10mm?
Attachment 168
Attachment 169
I cast and PC my own boolits.
I've been thinking about getting into casting, and reading a bit about painting and powder coating. Do you gas check the rifle bullets?
Well, way back when ebay sold once fired cases, I found a seller that was getting a lot of 10mm from a police practice range. After that on another board I got into a group buy for 500 new Starline nickel plated 10mm cases. 40 cal is always easy to find at the range and pick up for free, I have never bought any brass for it. I use the exact same 185 grain Precision Bullets for both calibers.
I also got lucky and bought out somebody's Lapua cases for 7.62X54R. And for a while I had a Lapua distributor selling them for $30/100, and I snarfed up about 600 cases. I loves to find deals on cases.
All I have to do with my last batch of processed brass is separate the .40 cal and 10mm cases by headstamp. They sure do look purdy.
I just chopped down ~1100 223/5.56 for 300aac last night. They'll go in the wet tumbler (without media) for a prewash and to remove any burrs today after work. Let em dry for a day or so and then I start trimming and sizing...
You do seem to like that caliber!;)
But why no media?
Mbaker78,
would you enlighten me on your process of cutting the 223 casings down?
I also like my 300aac, but use my HF mini cut off saw to cut the shoulders then form them in the die...it just seemsto be a tedious process!
It's easier to just rinse the brass off, I mainly just want to get rid of any brass dust and shavings from cutting. I'll run a proper batch with media after they've been sized and trimmed to spec.
I use the same process, just crank the music up and chop away. Up until I started wet tumbling, the worst part was the chamfer/deburr... It seems I can skip that step when wet tumbling :D
[QUOTEI use the same process, just crank the music up and chop away. Up until I started wet tumbling, the worst part was the chamfer/deburr... It seems I can skip that step when wet tumbling :D[/QUOTE]
So you use the wet tumble with steel and it takes most of the edge off?
So you use the wet tumble with steel and it takes most of the edge off?[/QUOTE]
What it does is remove a lot of the loose brass that is still hanging on after it gets cut. I've done around 750K doing it that way and it really helps keep loose brass out of the dies. Not to mention forming goes a bit easier with real clean cases.
Most guys that form the 300BO use an electric trimmer that mounts on a special die. Dillon came out with a newer beefier version of there older trimmer. I've never used the newer trimmer just the older version and it helps when it only has to trim just a few thousanths off the case....
I'd like to have a rapid trim, but the volume I do leaves it's price point out of my range... I'll have to stick with my Lyman trimmer with power drill adapter...
Though I can still crank about 100 in 45 minutes (the length of a TV show on Netflix) between sizing and trimming.
I loaded my First 45 colt rounds today.
First time with this cal. So looking for that perfect load..
Attachment 170
Those look like 230gr Speer lead round nose... I have a box that are destined to be run through my 1911 ;)
Your Correct....
My Cimarron OutLaw has a .450 Bore so I can Load .452 Boolits......